// -- DO NOT EDIT BELOW THIS LINE ------------------
// -- Bus protocol ports, do not add to or delete
Bus2IP_Clk, // Bus to IP clock
Bus2IP_Resetn, // Bus to IP reset
Bus2IP_Data, // Bus to IP data bus
Bus2IP_BE, // Bus to IP byte enables
Bus2IP_RdCE, // Bus to IP read chip enable
Bus2IP_WrCE, // Bus to IP write chip enable
IP2Bus_Data, // IP to Bus data bus
IP2Bus_RdAck, // IP to Bus read transfer acknowledgement
IP2Bus_WrAck, // IP to Bus write transfer acknowledgement
IP2Bus_Error // IP to Bus error response
// -- DO NOT EDIT ABOVE THIS LINE ------------------
); // user_logic

// -- ADD USER PARAMETERS BELOW THIS LINE ------------
// --USER parameters added here
// -- ADD USER PARAMETERS ABOVE THIS LINE ------------

// -- DO NOT EDIT BELOW THIS LINE --------------------
// -- Bus protocol parameters, do not add to or delete
parameter C_NUM_REG = 1;
parameter C_SLV_DWIDTH = 32;
// -- DO NOT EDIT ABOVE THIS LINE --------------------

// -- ADD USER PORTS BELOW THIS LINE -----------------
output [7:0] LED;
// -- ADD USER PORTS ABOVE THIS LINE -----------------

// -- DO NOT EDIT BELOW THIS LINE --------------------
// -- Bus protocol ports, do not add to or delete
input Bus2IP_Clk;
input Bus2IP_Resetn;
input [C_SLV_DWIDTH-1 : 0] Bus2IP_Data;
input [C_SLV_DWIDTH/8-1 : 0] Bus2IP_BE;
input [C_NUM_REG-1 : 0] Bus2IP_RdCE;
input [C_NUM_REG-1 : 0] Bus2IP_WrCE;
output [C_SLV_DWIDTH-1 : 0] IP2Bus_Data;
output IP2Bus_RdAck;
output IP2Bus_WrAck;
output IP2Bus_Error;
// -- DO NOT EDIT ABOVE THIS LINE --------------------

//----------------------------------------------------------------------------
// Implementation
//----------------------------------------------------------------------------

// --USER nets declarations added here, as needed for user logic

// Nets for user logic slave model s/w accessible register example
reg [C_SLV_DWIDTH-1 : 0] slv_reg0;
wire [0 : 0] slv_reg_write_sel;
wire [0 : 0] slv_reg_read_sel;
reg [C_SLV_DWIDTH-1 : 0] slv_ip2bus_data;
wire slv_read_ack;
wire slv_write_ack;
integer byte_index, bit_index;

// USER logic implementation added here
assign LED = slv_reg0[7:0];
// ------------------------------------------------------
// Example code to read/write user logic slave model s/w accessible registers
//
// Note:
// The example code presented here is to show you one way of reading/writing
// software accessible registers implemented in the user logic slave model.
// Each bit of the Bus2IP_WrCE/Bus2IP_RdCE signals is configured to correspond
// to one software accessible register by the top level template. For example,
// if you have four 32 bit software accessible registers in the user logic,
// you are basically operating on the following memory mapped registers:
//
// Bus2IP_WrCE/Bus2IP_RdCE Memory Mapped Register
// "1000" C_BASEADDR + 0x0
// "0100" C_BASEADDR + 0x4
// "0010" C_BASEADDR + 0x8
// "0001" C_BASEADDR + 0xC
//
// ------------------------------------------------------

assign
slv_reg_write_sel = Bus2IP_WrCE[0:0],
slv_reg_read_sel = Bus2IP_RdCE[0:0],
slv_write_ack = Bus2IP_WrCE[0],
slv_read_ack = Bus2IP_RdCE[0];

// implement slave model register(s)
always @( posedge Bus2IP_Clk )
begin